Development of a molecularly imprinted polymer on silanized graphene oxide for the detection of 17-estradiol in wastewater.

This research article demonstrates the synthesis, characterization, and electrochemical evaluation of a molecularly imprinted polymer (MIP) on the surface of silanized graphene oxide (silanized GO), which is nanostructured and used to quantify 17-estradiol (E2) in wastewater. As characterization methods, X-ray diffraction (XRD), Raman spectroscopy, dynamic scattering light (DSL), scanning electron microscope (SEM), and Fourier transform infrared spectroscopy (FTIR) were utilized to examine the synthesized GO, silanized GO, MIP-GO composite, and non-imprinted polymer (NIP)-GO (NIP-GO) composite. FTIR results confirmed the successful synthesis of GO composites. Raman study confirmed the synthesis of monolayer silanized GO, MIP-GO composite, and NIP-GO composite. Surface morphology revealed that after polymerization, the surface of silanized GO sheet-like morphology is covered with nanoparticles. Adsorption kinetics studies revealed that adsorption follows the pseudo-second-order kinetics. Further, we studied the performance of a MIP-GO-based sensor by optimizing the effects of pH, scan rate, and incubation period. The linear calibration was achieved between the oxidation peak current and E2 concentration from 0.1 to 0.81 ppm, with a detection limit of 0.037 ppm. The selectivity of the MIP-GO composite was also checked by using other estrogens, and it was found that E2 is 3.3, 0.5, and 1.4 times more selective than equilin, estriol, and estrone, respectively. The composite was successfully applied to the wastewater samples for the detection of E2, and a good percentage of recoveries were achieved. It suggests that the reported composite can be applied to real samples. PRACTITIONER POINTS: An innovative electrochemical sensor was developed for selective detection of 17-estradiol through molecularly imprinted polymer fabricated on the surface of silanized GO (MIP-GO composite). The developed method was comprehensively validated and found to be linear in the range of 0.1 to 0.8 ppm of 17-estradiol, with 0.037 ppm of limit of detection and 0.1 ppm of limit of quantification, respectively. The developed MIP-GO-composite-based electrochemical sensor was found 3.3, 0.5, and 1.4 times more selective for 17-estradiol than equiline, estriol, and estrone, respectively. The applicability of a developed sensor was also checked on wastewater samples, and a good percent recovery was obtained.

Isothermal titration calorimetry binding properties of Cibacron Blue F3GA in complex with human serum albumin.

Binding interactions between Cibacron Blue-F3GA (CB-F3GA) and human serum albumin (HSA, at physiologically ten-fold lower concentration) was studied by isothermal titration calorimetry (ITC) and in-silico docking computations. ITC experiments revealed two separate binding sites on HSA with different binding affinities for CB-F3GA. The high-affinity binding site (PBS-II) on HSA binds CB-F3GA at nanomolar scale (KD1 = 118 ± 107 nM) with favorable binding enthalpy (ΔHo 1 = - 6.47 ± 0.44 kcal/mol) and entropy (-TΔSo 1 = -2.98 kcal/mol) energies. CB-F3GA binds to the low-affinity binding site (PBS-I) at µM scale (KD2 = 31.20 ± 18.40 µM) with favorable binding enthalpy (ΔHo 1 = - 5.03 ± 3.86 × 10-2 kcal/mol) and entropy (-TΔSo 1 = -1.12 kcal/mol) energies. ITC binding data strongly suggest that CB-F3GA binding to PBS-II site increases the formation of dimeric-HSA clusters (N1 = 2.43 ± 0.50), while binding to PBS-I leads to tetrameric-HSA clusters (N2 = 4.61 ± 0.90). These results suggest that a higher degree of HSA aggregation upon drug binding may be expected under physiological conditions, a notion that should be further investigated for the delivery and toxicity of drug-HSA interactions.

Molecularly Designed Ion-Imprinted Nanoparticles for Real-Time Sensing of Cu(II) Ions Using Quartz Crystal Microbalance.

A molecularly designed imprinting method was combined with a gravimetric nanosensor for the real-time detection Cu(II) ions in aqueous solutions without using expensive laboratory devices. Thus, 1:1 and 2:1 mol-ratio-dependent coordination modes between Cu(II), N-methacyloly-L histidine methyl ester (MAH) functional monomer complexes, and their four-fold and six-fold coordinations were calculated by means of density functional theory molecular modeling. Cu(II)-MIP1 and Cu(II)-MIP2 nanoparticles were synthesized in the size range of 80-100 nm and characterized by SEM, AFM and FTIR. Cu(II)-MIP nanoparticles were then conducted to a quartz crystal microbalance sensor for the real-time detection of Cu(II) ions in aqueous solutions. The effects of initial Cu(II) concentration, selectivity, and imprinting efficiency were investigated for the optimization of the nanosensor. Linearity of 99% was obtained in the Cu(II) ion linear concentration range of 0.15-1.57 µM with high sensitivity. The LOD was obtained as 40.7 nM for Cu(II)-MIP2 nanoparticles. The selectivity and the imprinting efficiency of the QCM nanosensor were obtained significantly in the presence of competitive ion samples (Co(II), Ni(II), Zn(II), and Fe(II)). The results are promising for sensing Cu(II) ions as environmental toxicants in water by combining molecularly designed ion-imprinted nanoparticles and a gravimetric sensor.

Recognition of human hemoglobin with macromolecularly imprinted polymeric nanoparticles using non-covalent interactions.

Hemoglobin (Hb) is the most abundant protein in the blood. It is vital for the living as oxygen carriers. Some of the very pure Hb-containing biological fluids are currently under clinical trial. However, the removal and purification of Hb from the blood are quite difficult, especially when it is at a low concentration level. In this study, the molecularly imprinted polymeric nanoparticles (MIPNs) were prepared using N-methacryloyl-histidine methyl ester (MAH) by mini-emulsion polymerization technique for specific binding of human hemoglobin (HHb). MIPNs in monosize form have a size of 152 ± 4 nm. They also have a high binding capacity (32.33 mg/g) of HHb. MIPNs retain 84% of the re-binding capacity for HHb after 10 cycles. The nanoparticles have 16 and 5 times higher binding capacity of HHb, respectively, in the presence of bovine serum albumin and lysozyme. Thanks to their high binding capacity and selectivity, MIPNs will allow them to be detected selectively for different target molecules. According to molecular docking, the main binding forces depend on hydrogen bonds and Van der Waals forces in the interaction within 5 Å around MAH molecule are observed through the amino acid residues of HHb at ß1 and ß2 subunit. The statistical mechanical analysis of docking showed that the free energy (ΔG) is -2732.14 kcal/mol, which indicates the interaction between MAH and HHb is energetically favorable at 298.15°K.

Binding modes of cibacron blue with albumin in affinity chromatography using docking tools.

Affinity chromatography is a standard method, which used for protein purification and separation studies due to its specificity and selectivity. There are several affinity chromatography methods, such as dye affinity, immobilized metal chelated affinity, and affinity electrophoresis. Cibacron Blue F3G-A (CBD), as a dye ligand, is one of the most used dyes among dye affinity chromatography. CBD is ideally suited for human serum albumin (HSA) separation and purification in affinity chromatography for several years. However, even though CBD has many purification applications, there is not much research focused on the interaction between CBD and HSA in molecular docking. The interactions between CBD and HSA were simulated via AutoDock molecular docking software in this study. Investigated possibilities resulted in six different conformations on different locations, which light the way to variable connectivity of CBD. Thus, it was determined that the most favorable binding is conformation 5, with its lowest binding energy, which is energetically favorable.

Molecular docking of metal ion immobilized ligands to proteins in affinity chromatography.

Immobilized metal ion affinity chromatography (IMAC) has become a widespread analytical and preparative separation method for therapeutic proteins, peptides nucleic acids, hormones, and enzymes. N-Methacryloyl-l-histidine Methyl Ester (MAH) monomer is recently used as a synthesized affinity ligand in IMAC. It is capable of chelating with many transition metal ions such as Zn2+ , Ni2+ , and Cu2+ ions through its histidine residue. In this way, proteins can bind selectively to these immobilized metal ions through MAH as a ligand in affinity chromatography. In this study, we applied the computational docking method on the interactions that occur between the MAH monomer and its complexes with Zn2+ ions as ligands and protein molecules as targets. MAH monomer was drawn and created using the Avogadro software as an optimization tool. Human insulin (Ins) molecule and horse heart cytochrome C (Cyt C) were selected as target proteins to interact with MAH monomer as affinity ligand. Automated docking software AutoDock v4.2 was used for docking of MAH monomer to Ins and Cyt C, respectively. The affinity ligand complexes with Zn2+ ions bound to one, two, and three moles of MAH were studied and compared separately. The lowest binding energies of Ins and Cyt C proteins in 1:1 mol ratio of MAH-Zn2+ were found as (-4.14) and (-4.92) kcal/mol, respectively.

Composite Polymeric Cryogel Cartridges for Selective Removal of Cadmium Ions from Aqueous Solutions.

In this study, composite polymeric cryogel cartridges were achieved by using Cd(II) imprinted poly(hydroxyethyl methacrylate N-methacryloly-(L)-cysteine methylester) beads and poly(hydroxyethyl methacrylate) cryogel cartridges with two different mole ratios of functional monomer. The N-methacryloly-(L)-cysteinemethylester was used as a functional monomer and Cd(II) 1:1 and 2:1, which were then notated as MIP1 and MIP2, respectively. Various characterization methods have confirmed the structural transformation on the MIP1 and MIP2 composite cryogel cartridges by scanning electron microscopy, Fourier-transform infrared spectroscopy-Attenuated Total Reflectance, and swelling tests. The maximum amount of Cd(II) adsorption with composite cryogel cartridges was determined by altering the Cd(II) initial concentration, temperature, and pH values. The maximum adsorption capacity of MIP1 and MIP2 composite cryogel cartridges obtained was 76.35 and 98.8 µmol/g of composite cryogels, respectively. The adsorption studies revealed that the MIP2 possessed a good adsorption performance for Cd(II). The obtained composite cryogel cartridges have a selective, reusable, and cost-friendly potential for the removal of Cd(II) from aqueous solutions, and are used many times without decreasing their adsorption capacities significantly. The Cd(II) removal rate of the MIP1 and MIP2 composite cryogel cartridges from synthetic wastewater samples was determined as 98.8%. The obtained cryogel cartridges' adsorption material exhibited a good directional removal performance for Cd(II) from wastewater samples.

Molecularly Imprinted Polymers for Removal of Metal Ions: An Alternative Treatment Method.

Aquatic and terrestrial environment and human health have been seriously threatened with the release of metal-containing wastewater by the rapid growth in the industry. There are various methods which have been used for removal of ions from the environment, such as membrane filtration, ion exchange, membrane assisted liquid extraction and adsorption. As a sort of special innovation, a polymerization technique, namely molecular imprinting is carried out by specific identification for the target by mixing it with a functional monomer. After the polymerization occurred, the target ion can be removed with suitable methods. At the end of this process, specific cavities, namely binding sites, are able to recognize target ions selectively. However, the selectivity of the molecularly imprinted polymer is variable not only because of the type of ligand but also charge, size coordination number, and geometry of the target ion. In this review, metal ion-imprinted polymeric materials that can be applied for metal ion removal from different sources are discussed and exemplified briefly with different metal ions.

Surface imprinted bacterial cellulose nanofibers for hemoglobin purification.

There is a significant need for the development of the novel adsorbents in the field of protein purification. In this study, thin hemoglobin imprinted film (MIP) was fabricated onto the bacterial cellulose nanofibers' (BCNFs) by surface imprinting method using metal ion coordination interactions with N-methacryloyl-(L)-histidinemethylester (MAH) and copper ions. The hemoglobin surface imprinted bacterial cellulose nanofibers (MIP-BCNFs) was applied to selective recognition of hemoglobin and purification from hemolysate. The characterization of the MIP-BCNFs was carried out by the Fourier Transformed Infrared Spectroscopy (FT-IR), Scanning Electron Microscopy (SEM), micro-Computerized Tomography (µCT), atomic force microscopy (AFM) and surface area measurements. The adsorption experiments of hemoglobin onto the MIP-BCNFs and NIP-BCNFs from aqueous hemoglobin solutions were investigated in a batch system. The results showed that MIP-BCNFs are promising materials for purification of hemoglobin with high adsorption capacity, significant selectivity and reusability.

Affinity binding of proteins to the modified bacterial cellulose nanofibers.

The potential of the modified bacterial cellulose (BC) nanofibers was determined bearing metal ion coordination interactions to enhance the protein adsorption and binding capacity. Thus, a household synthesized metal chelating monomer, namely N-methacryloyl-l-histidine methylester (MAH), and a commercial metal chelating monomer, namely 4-vinylimidazole (VIm), were used to complex with metal ions Cu(II) and Ni(II) respectively for the synthesis of the modified BC nanofibers. The modified nanofibers were characterized by FT-IR, SEM and EDX measurements. The protein adsorption tests were carried out using hemoglobin as a model protein and it was determined that the maximum adsorption capacity of hemoglobin onto the modified BC nanofibers was found as 47.40mg/g. The novel strategy for the preparation of metal chelated nanofibers was developed.

Affinity based and molecularly imprinted cryogels: Applications in biomacromolecule purification.

The publications in macro-molecularly imprinted polymers have increased drastically in recent years with the development of water-based polymer systems. The macroporous structure of cryogels has allowed the use of these materials within different applications, particularly in affinity purification and molecular imprinting based methods. Due to their high selectivity, specificity, efficient mass transfer and good reproducibility, molecularly imprinted cryogels (MICs) have become attractive for researchers in the separation and purification of proteins. In this review, the recent developments in affinity based cryogels and molecularly imprinted cryogels in protein purification are reviewed comprehensively.

Molecularly imprinted cryogels for human serum albumin depletion.

Molecularly imprinted polymers can be used for the selective capture of a target molecule from complex medium. Cryogels novel matrices, which characterized by their supermacropores that makes their use advantageous when studying with biological samples. By combining high selectivity of the molecular imprinting approach with using cryogel as a base polymer, in this protocol, preparation of the albumin-imprinted cryogels is described. This material is a useful candidate for the selective albumin depletion from the human serum sample prior to the detailed proteomic analysis.

Dye-attached magnetic poly(hydroxyethyl methacrylate) nanospheres for albumin depletion from human plasma.

The selective binding of albumin on dye-affinity nanospheres was combined with magnetic properties as an alternative approach for albumin depletion from human plasma. Magnetic poly(hydroxyethyl methacrylate) (mPHEMA) nanospheres were synthesized using mini-emulsion polymerization method in the presence of magnetite powder. The specific surface area of the mPHEMA nanospheres was found to be 1302 m(2)/g. Subsequent to Cibacron Blue F3GA (CB) immobilization onto mPHEMA nanospheres, a serial characterization processing was implemented. The quantity of immobilized CB was calculated as 800 µmol/g. Ultimately, albumin adsorption performance of the CB-attached mPHEMA nanospheres from both aqueous dissolving medium and human plasma were explored.

Cibacron blue immobilized poly(glycidyl-methacrylate) nanobeads for albumin removal in proteome studies.

A new approach to albumin removal for proteome studies involving human plasma samples was presented with dye affinity poly glycidyl methacrylate (PGMA) nanobeads in an average size of 45 nm. The specific surface area of PGMA nanobeads was calculated as 2616 m(2)/g. Cibacron Blue F3GA (CB) was immobilized onto PGMA nanobeads as dye ligand, and CB immobilized PGMA (CB-PGMA) nanobeads were characterized by a serial processing. Albumin depletion efficiency of CB-PGMA nanobeads was investigated in human plasma sample and confirmed by two-dimensional gel electrophoresis.

Composite cryogels for lysozyme purification.

Beads-embedded novel composite cryogel was synthesized to purify lysozyme (Lyz) from chicken egg white. The poly(hydroxyethyl methacrylate-N-methacryloyl-L-phenylalanine) (PHEMAPA) beads of smaller than 5 µm size were synthesized by suspension polymerization and then embedded into a poly(hydroxyethyl methacrylate) (PHEMA)-based cryogel column. The PHEMAPA bead-embedded cryogel (BEC) column was characterized by swelling tests, scanning electron microscopy (SEM), surface area measurements by the Brunauer-Emmett-Teller (BET) method, elemental analysis, and flow dynamics. The specific surface area of the PHEMAPA BEC was found as 41.2 m(2) /g using BET measurements. Lyz-binding experiments were performed using aqueous solutions in different conditions such as initial Lyz concentration, pH, flow rate, temperature, and NaCl concentration of an aqueous medium. The PHEMAPA BEC column could be used after 10 adsorption-desorption studies without any significant loss in adsorption capacity of Lyz. The PHEMAPA BEC column was used to purify Lyz from chicken egg white, and gel electrophoresis was used to estimate the purity of Lyz. The chromatographic application of the PHEMAPA BEC column was also performed using fast protein liquid chromatography.

Molecularly imprinted composite cryogels for hemoglobin depletion from human blood.

A molecularly imprinted composite cryogel (MICC) was prepared for depletion of hemoglobin from human blood prior to use in proteome applications. Poly(hydroxyethyl methacrylate) based MICC was prepared with high gel fraction yields up to 90%, and characterized by Fourier transform infrared spectrophotometer, scanning electron microscopy, swelling studies, flow dynamics and surface area measurements. MICC exhibited a high binding capacity and selectivity for hemoglobin in the presence of immunoglobulin G, albumin and myoglobin. MICC column was successfully applied in fast protein liquid chromatography system for selective depletion of hemoglobin for human blood. The depletion ratio was highly increased by embedding microspheres into the cryogel (93.2%). Finally, MICC can be reused many times with no apparent decrease in hemoglobin adsorption capacity.

Molecularly imprinted poly(hydroxyethyl methacrylate) based cryogel for albumin depletion from human serum.

Macroporous cryogels imprinted with human serum albumin (HSA) have been prepared by copolymerization of 2-hydroxyethyl methacrylate with a functional co-monomer of N-methacryloyl-L-phenylalanine. The cryogels were used for the depletion of HSA from human serum. HSA-imprinted cryogels were prepared with gel fraction yields up to 90%, and their chemical structure, morphology and porosity were characterized by FTIR-spectroscopy, scanning electron microscopy, swelling studies and flow dynamics. Selective binding experiments were performed in the presence of competitive proteins like human transferrin and myoglobin. Albumin-imprinted cryogel column was optimized for fast protein liquid chromatography. Sodium-dodecyl sulfate polyacrylamide gel electrophoresis was used to show the efficiency of albumin depletion.

Synthesis and characterization of amino acid containing Cu(II) chelated nanoparticles for lysozyme adsorption.

Immobilized metal ion affinity chromatography (IMAC) is a useful method for adsorption of proteins that have an affinity for transition metal ions. In this study, poly(hydroxyethyl methacrylate-methacryloyl-L-tryptophan) (PHEMATrp) nanoparticles were prepared by surfactant free emulsion polymerization. Then, Cu(II) ions were chelated on the PHEMATrp nanoparticles to be used in lysozyme adsorption studies in batch system. The maximum lysozyme adsorption capacity of the PHEMATrp nanoparticles was found to be 326.9 mg/g polymer at pH 7.0. The nonspecific lysozyme adsorption onto the PHEMA nanoparticles was negligible. In terms of protein desorption, it was observed that adsorbed lysozyme was readily desorbed in medium containing 1.0 M NaCl. The results showed that the metal-chelated PHEMATrp nanoparticles can be considered as a good adsorbent for lysozyme purification.

Molecularly imprinted composite cryogel for albumin depletion from human serum.

A new composite protein-imprinted macroporous cryogel was prepared for depletion of albumin from human serum prior to use in proteom applications. Polyhydroxyethyl-methacylate-based molecularly imprinted polymer (MIP) composite cryogel was prepared with high gel fraction yields up to 83%, and its morphology and porosity were characterized by Fourier transform infrared, scanning electron microscopy, swelling studies, flow dynamics, and surface area measurements. Selective binding experiments were performed in the presence of competitive proteins human transferrin (HTR) and myoglobin (MYB). MIP composite cryogel exhibited a high binding capacity and selectivity for human serum albumin (HSA) in the presence of HTR and MYB. The competitive adsorption amount for HSA in MIP composite cryogel is 722.1 mg/dL in the presence of competitive proteins (HTR and MYB). MIP composite cryogel column was successfully applied in the fast protein liquid chromatography system for selective depletion of albumin in human serum. The depletion ratio was highly increased by embedding beads into cryogel (85%). Finally, MIP composite cryogel can be reused many times with no apparent decrease in HSA adsorption capacity.

Dye attached poly(hydroxyethyl methacrylate) cryogel for albumin depletion from human serum.

Cibacron Blue F3GA was immobilized on poly(hydroxyethyl methacrylate) cryogel and it was used for selective and efficient depletion of albumin from human serum. The poly(hydroxyethyl methacrylate) was selected as the basic component because of its inertness, mechanical strength, chemical and biological stability, and biocompatibility. Cibacron Blue F3GA was covalently attached to the poly(hydroxyethyl methacrylate) cryogel to produce poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel affinity column. The poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel was characterized with respect to gelation yield, swelling degree, total volume of macropores, Fourier Transform Infrared spectroscopy, and scanning electron microscopy. It was found that the maximum amount of adsorption (343 mg/g of dry cryogel) obtained from experimental results is very close to the calculated Langmuir adsorption capacity (345 mg/g of dry cryogel). The maximum adsorption capacity for poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel column was obtained as 950 mg/g of dry cryogel for nondiluted serum. The adsorption capacity decreased with increasing dilution ratios while the depletion ratio of albumin remained as 77% in serum sample. Finally, the poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel was optimized for using in the fast protein liquid chromatography system for rapid removal of the high abundant proteins from the human serum.